Buy the best PA3467U-1ACA ac adapter, repair PA3467U-1ACA ac adapter

PRLog (Press Release) – Sep 08, 2009 – Many people are fond of Toshiba. When the nice feet stepped on the cable the laptop practiced flying, fortunately almost without further consequences. But the PA3467U-1ACA ac adapter plug did not fit any more. The golden tip of the sophisticated laptop ac adapter even preferred to remain inside of the laptop and was not easily be convinced to leave. What's to be done now?

The shell could be removed. As suspected from the charging light toy effects before, there are some electronics inside. The cable had two wires, the black one ending next to some semiconductor, the grey one between two resistors. Removed the cable. Formerly, the inner contacts of the PA3467U-1ACA ac adapter connector must have looked very similar to a simple 2.5mm TRS (tip-ring-sleeve) jack. Here I have pulled the damaged parts out.

The shield should be readjusted to some cylindrical shape. To have a look at the inner parts, the PA3467U-1ACA ac adapter light guide will have to be removed. Slice it. To remove the shield it should be dilated. And don't forget desoldering. The PA3467U-1ACA ac adapter replacement TRS jack is not gold plated like the delicate original but it seems quite robust.

After estimated the correct length, connect to the appropriate holes of the PCB. So it looks from the other side. Please note the solder securing the S contact. Without that lots of new TRS jacks are unusable. The outer shield in its original shape would short circuit TRS contacts, remove some of it. For a first test of what we have done use a piece of tubing to isolate the outer shield and connect the wires. If you all survived the test it's time for putting the PA3467U-1ACA ac adapter connector together. First spend some epoxy glue for isolation.

Smoothing the light guide's gash provides some room for the glue afterwards. There is not plenty of room. Be careful not to perforate the insulation of the laptop ac adapter wires. The light guide's fissure will be filled with a drop of transparent epoxy glue.

To prepare it the terminals should be tinned using some acid flux. And the usual weak internal connections in this type of TRS jack can be secured by soldering. Be quick enough not to melt the plastic rings in the tip. Contacts will have to be prepared to fit the printed circuit board (PCB). Cut a bit away from the S (sleeve) and the R (ring) contacts and laptop ac adapter connect wires for T (tip) and R (ring).

Toshiba PA3467U-1ACA AC Adapter Description:

Input: AC100-240V (worldwide use)

Output: DC19V 3.42A

Power: 65W

Outlet: 2-prong

Connecter size:  

   Internal Diameter: 2.5mm

   External Diameter: 5.5mm

Item Includes: AC Adapter and Power Cord

Performance: Short Circuit Protection and Overload Protection

Condition: new

100%OEM compatible, guaranteed to meet or exceed OEM specifications!

Compatible Part Numbers

PA3396U-1ACA, PA-1650-01, PA3467U-1ACA, ADP-65DB, ADP-65HB, PA-1700-02, SADP-65KB, LC-T2801-006,  PA-1480-19Q

Note: These instructions are given without any warranty. They don't have to be complete or correct. Don't do any of the following steps if you're not sure of what you're doing. You could damage your notebook and you WILL lose your warranty. Everything you do will be at your own risk.

See more information on:    http://www.papatek.com/Toshiba-PA3467U-1ACA/

# # #

http://www.papatek.com locates in Santa Clara, is a direct sales office and service center of our replacement IT parts manufacture. We currently supply brand new AC Adapter, Rechargeable Battery, DVDRW Drive, LCD Panel, Laptop Keyboard, Floppy Disk Drive and many others for almost all name brand laptops and printers.

• RBT 1.3.1 (Freeware)